Flashing
Termination bar, pipe boots and edge metal are installed to keep water out.
Flat Roofing
Rubber Roof Installation Short Hills, NJ
A Short Hills roofer who installs EPDM can put a new rubber roof on a flat or low slope section of almost any home, with as few seams as possible. Dial (862) 424-5211 to talk with a local roofer about a new rubber roof.
EPDM is the material most people mean when they say rubber roof. EPDM is sold in wide rolls, typically 45 or 60 mil thick, and it stretches and recovers as the roof moves through hot and cold seasons. Unlike TPO and PVC, its seams are taped rather than heat welded.
The first decision is how the membrane is held down. Adhered, fastened and ballasted systems each suit different buildings and wind conditions. On most homes, fully adhered EPDM is the usual choice because it handles wind well and stays smooth.
Two more decisions round out the plan. A 60 mil sheet is tougher than 45 mil for roofs that see foot traffic. Black EPDM absorbs heat, which helps in cold climates, while white EPDM reflects sun and keeps rooms below cooler. The transition to a steeper roof or a wall is planned with the same care, since that is where low roofs most often leak.
If the problem goes deeper than it first looked, a Short Hills roofer may also recommend rubber roof repair or flat roof installation.
Looking for Short Hills rubber roof installation? Call (862) 424-5211 and describe the problem to a roofer who works in Short Hills.
Call nowThe process
The rubber roof installation process
Here is how a roofer typically installs an EPDM roof.
Deck prep
The roofer checks the deck for rot, gaps and loose sheets and confirms the roof has enough slope to drain. A tear-off comes first on existing roofs.
Install insulation
Rigid insulation, often polyiso, is fastened with plates and screws, then a cover board goes on top. Low spots can be corrected with tapered insulation.
Roll out the membrane
The membrane is unrolled, aligned and allowed to settle before bonding. Laps are arranged so water flows over them.
Apply adhesive
Half the sheet is folded back, adhesive is applied to both surfaces and the rubber is pressed into place. The process repeats for the second half. Air pockets left under the sheet can turn into blisters later, so the crew works the rubber flat from the center out.
Seal the seams
Laps are primed and joined with seam tape, then rolled to remove air. Tape edges are finished with lap sealant.
Finish the edges
Perimeter edge metal, wall flashing and pipe boots complete the roof. Counter flashing covers the top of wall flashing. A final walk checks every seam with a probe before the job is closed out.
What is included
Parts of a new EPDM roof
Cover board
Insulation adds energy savings and slope under the rubber.
Rubber sheet
The rubber membrane is adhered or fastened with as few seams as possible.
Seam tape
Seams are primed, taped and rolled for a lasting bond.
Deck preparation
The base is cleared and checked before new layers go down.
Related service
EPDM Roof Installation Short Hills, NJ
The quality of an EPDM installation shows up years later in the seams and edges. Rushing the adhesive, skipping primer or leaving wrinkles under the sheet are the common mistakes. Dry, mild days give the best bond. Some installers use water-based adhesive for the field of the roof and solvent-based adhesive at walls and curbs, where the grip has to be strongest.
For a Short Hills home, the installer thinks ahead to how the roof will behave over the years. Securing the membrane at the edges and flashing corners correctly prevents later tears. Ask about edge securement before work starts.
Local help
Rubber Roof Installation Near Me
In Short Hills, EPDM is a popular choice for low slope roofs on additions and attached garages. Across Short Hills and nearby towns like Springfield, Summit, Vauxhall and Chatham, EPDM handles storms, sun and cold well when it is installed with good seams and drainage, which is why the seams and flashing deserve careful attention.
Need rubber roof installation around Short Hills? Call (862) 424-5211 for a Short Hills roofer who serves the towns around it too.
Roofs in this climate
Winters here are long and cold, with snow on the roof for weeks at a time and plenty of nights below freezing. Heat escaping from the attic melts snow on the upper roof, and the water refreezes at the colder eaves, which is how ice dams form and back water up under the shingles. Coastal storms and heavy spring rain drive water sideways into flashing, valleys and old chimneys. That is why roof repair in Short Hills is busiest after a hard winter and before the next one.
Why call
Why not wait
Less damage
Small roof problems caught early usually stay small repairs.
Roofers who know Short Hills
Roofers in Short Hills know the roof types and weather wear common in local homes.
Clear next steps
Ask your questions before you agree to anything.
Common questions about rubber roof installation
Is a rubber roof the same as TPO?
The two are different materials. Black EPDM is taped and stretchy, and white TPO is welded and reflective. A roofer can help you choose.
What is the lifespan of a new EPDM roof?
Rubber roofs often last decades. Thickness, seam quality and maintenance all affect its life. Repairs are simple when needed.
Which EPDM thickness should I choose?
The common choices are 45 mil and 60 mil. The thicker sheet holds up better to traffic and weather. Even thicker sheets are available for demanding roofs.
Should my rubber roof be black or white?
The choice depends on the climate and the space below. Black EPDM absorbs heat, which can help in cold climates, while white EPDM reflects sunlight and keeps the rooms below cooler. A roofer can recommend what fits your home.
Is it possible to install EPDM over the old roof?
A recover is possible only under certain conditions. Codes generally allow one recover over a dry, sound roof. Wet insulation or multiple layers mean a tear-off. Core samples or a moisture scan show whether the old roof is dry enough.
More questions? Call (862) 424-5211
Often needed together
Rubber Roof Repair
Repairs for leaking rubber roofs, from peeling seams to pulled flashing at walls and curbs, after the real leak point is found.
Learn moreFlat Roof Installation
Flat roof installation from the deck and tapered insulation up to the seams, flashing and edge metal, so water drains instead of ponding.
Learn moreTPO Roofing
White, heat-welded TPO single-ply roofing for low-slope homes and buildings, with seams welded into one watertight sheet.
Learn moreFlat Roof Replacement
Full replacement of failing flat roofs, with a moisture survey deciding tear-off or recover, so ponding and repeat leaks end for good.
Learn more
Looking for something else?
See all roofing servicesGet rubber roof installation help in Short Hills
Call now for Short Hills rubber roof installation and help in the towns around it.